[Synce-devel] iPAQ not recognized by kernel

[Bob]

Kernel/system info:
Linux IBFX-IT-08 2.6.15-26-686 #1 SMP PREEMPT Thu Aug 3 03:13:28 UTC
2006 i686 GNU/Linux

Device info:
HP iPAQ hx2415

USB info:

T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.01 Cls=ff(vend.) Sub=ff Prot=ff MxPS=16 #Cfgs= 1
P: Vendor=03f0 ProdID=1016 Rev= 0.00
S: Manufacturer=Intel.
S: Product=PocketPC SmartPhone
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms

[David Eriksson]

Post by Bob
Linux IBFX-IT-08 2.6.15-26-686 #1 SMP PREEMPT Thu Aug 3 03:13:28 UTC
2006 i686 GNU/Linux
HP iPAQ hx2415
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.01 Cls=ff(vend.) Sub=ff Prot=ff MxPS=16 #Cfgs= 1
P: Vendor=03f0 ProdID=1016 Rev= 0.00
S: Manufacturer=Intel.
S: Product=PocketPC SmartPhone
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms

What if you manually load the "ipaq" kernel module?

\David
--

[Bob]

Yeah, it recognizes it just fine then.. I just sent off the email
cause the howto mentioned it..

As for getting it all working, no go.. Mostly because of some missing
packages.. And being at work, I didn't want to spend tons of time on
it.. Anyway, I plan to remove the packages that I installed today
using APT and synaptic and install from the source packages on the
site..

If I run into any large obstacles, I'll join the forum and post the
info in.. Thanks for the reply..

Bob

Post by David Eriksson

Post by Bob
Linux IBFX-IT-08 2.6.15-26-686 #1 SMP PREEMPT Thu Aug 3 03:13:28 UTC
2006 i686 GNU/Linux
HP iPAQ hx2415
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.01 Cls=ff(vend.) Sub=ff Prot=ff MxPS=16 #Cfgs= 1
P: Vendor=03f0 ProdID=1016 Rev= 0.00
S: Manufacturer=Intel.
S: Product=PocketPC SmartPhone
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms

What if you manually load the "ipaq" kernel module?
\David